Metallurgical Processes and Thermodynamics Open access Peer reviewed

Meniscus Flow and Strand Bulging Effects on Slag Skin Formation During Initial Solidification in the Continuous Casting Mold

Alexander Vakhrushev, Ebrahim Karimi‐Sibaki, Mohamad Al-Nasser, Abdellah Kharicha and 6 more

Metallurgical and Materials Transactions B | Nov 2, 2026

Abstract

Abstract

Abstract Continuous casting slag plays dominant role in the protecting fresh melt from the re-oxidation and heat losses at the meniscus region, as well as predefines heat transfer and lubrication phenomena at the gap between the solidifying shell and water-cooled copper mold. We developed a multiphase model for the coupled liquid steel–mold slag system that resolves transient flow in both the melt and the liquid slag and couples it with conjugate heat transfer across the interface. Steel melt solidification is included via latent heat release, and the solid slag skin formation and remelting are represented by evolving liquid, mushy, and solid sublayers. A key novelty is the consistent treatment of the inlet-throughput balance, which allows back-pressure pumping of the liquid core, for example due to bulging. Slag is fed into or rejected from the shell–mold gap based on the local pressure–shear balance, so mold powder consumption is not prescribed but emerges from mass conservation and the governing balances without ad hoc forcing. The 2D configuration was applied to isolate the core mechanisms linking mold flow, initial solidification, and slag skin infiltration, while the underlying geometric VOF formulation with sharp interfacial interpolation is written in vector–tensor form. The underlying formulation is not intrinsically restricted to 2D and can in principle be extended to 3D industrial cases. The model was applied to a representative case at a casting speed of 1.2 m/min and verified against state-of-the-art literature and plant observations, showing agreement with (i) slab surface temperatures, (ii) mold heat flux and hot-face temperature distributions, (iii) the analytical Bikerman meniscus profile, (iv) casting speed-scaled mold flux consumption trends, and (v) surface defects observed on final products. Simulations in the stable operating regime reveal surface ripples governed by a small set of dominant coherent oscillation modes. The predicted ripple depth is typically about 20 μ m, with occasional extremes of 40 to 50 μ m, well below typical mold oscillation marks. Even in this quasi-steady regime, the meniscus exhibits a weak time-dependent “breathing,” where small level and gap fluctuations promote intermittent Bikerman-type overflow of the shell tip and leave wavy surface imperfections. Bulging was prescribed using a roller pitch of 200 mm, giving a forcing frequency of 0.1 Hz (mode M1) at the casting speed of 1.2 m/min and higher harmonics at 0.2, 0.3 and 0.4 Hz (modes M2 to M4), generated by periodic shell deformation between support rolls and transmitted upward to the meniscus. Second-harmonic generation was observed even without explicit superposition of the meniscus oscillation modes, associated with a resonance-like response in defect-prone scenarios. Deep surface defects formation and underlying mechanisms, including cold-slag pumping and subsequent hooks freezing, were studied for bulging-induced mold-level oscillations. These effects were found to become particularly critical for the higher-frequency modes despite their net amplitude. Superposition of the main bulging modes produced sharper meniscus velocity and acceleration transients, resulting in increased surface defect depth. The relative phase shift between the superimposed modes was further identified as an additional governing parameter that modifies the instantaneous meniscus dynamics and, consequently, the resulting defect formation.

Direct answer

What can I do from this paper page?

Use this page to scan "Meniscus Flow and Strand Bulging Effects on Slag Skin Formation During Initial Solidification in the Continuous Casting Mold" quickly: start with the summary and abstract, then check the authors, source, topics, and related papers. From here, open Scollr to follow Metallurgical Processes and Thermodynamics research, save the paper, or map adjacent work.

Authors

Researchers on this paper

Alexander Vakhrushev

first | Montanuniversität Leoben

Ebrahim Karimi‐Sibaki

middle | Montanuniversität Leoben | ORCID 0000-0002-2275-6699

Mohamad Al-Nasser

middle | Montanuniversität Leoben | ORCID 0000-0001-7100-3186

Abdellah Kharicha

middle | Montanuniversität Leoben | ORCID 0000-0001-8636-2368

Menghuai Wu

middle | Montanuniversität Leoben

Gernot Hackl

middle | RHI Magnesita (Austria)

Yong Tang

middle | RHI Magnesita (Austria)

Josef Watzinger

middle | Primetals Technologies (Austria)

Veit Humer

middle | Primetals Technologies (Austria)

Jan Bohacek

last | Brno University of Technology

Research areas

Follow related topics

Citation

BibTeX

@article{Vakhrushev2026Meniscus,
  title = {Meniscus Flow and Strand Bulging Effects on Slag Skin Formation During Initial Solidification in the Continuous Casting Mold},
  author = {Alexander Vakhrushev and Ebrahim Karimi‐Sibaki and Mohamad Al-Nasser and Abdellah Kharicha and Menghuai Wu and Gernot Hackl and Yong Tang and Josef Watzinger and Veit Humer and Jan Bohacek},
  journal = {Metallurgical and Materials Transactions B},
  year = {2026},
  doi = {10.1007/s11663-026-04306-7},
  url = {https://doi.org/10.1007/s11663-026-04306-7}
}

FAQ

Using this paper in a discovery workflow

How do I find related work for this paper?

Use the related papers and topic links on this page as starting points. In Scollr, you can also open the paper and build a literature map around its references, citing papers, and related work.

How can I keep up with new Metallurgical Processes and Thermodynamics research papers?

Follow Metallurgical Processes and Thermodynamics research in Scollr. New papers from the topic flow into a personalized feed, and you can save useful studies to revisit later.

Can I cite this paper from this page?

This page includes a static BibTeX block for Meniscus Flow and Strand Bulging Effects on Slag Skin Formation During Initial Solidification in the Continuous Casting Mold. Always verify the DOI, source, and publication details against the publisher record before submitting a manuscript.

Follow this research in Scollr

Follow the topics and authors behind this paper, save useful studies, and build a literature map when you are ready to go deeper.

Get the app