Laser-Ablation Synthesis of Nanoparticles Open access Peer reviewed

Kinetically controlled boron carbide composite sub-micrometer particle formation pathways during continuous-flow laser melting in liquids with high-power lasers

Nico Koch, Christoph Rehbock, Naoto Koshizaki, Stephan Barcikowski

Beilstein Journal of Nanotechnology | Nov 10, 2026 | 1 citation

Abstract

Abstract

Monodisperse, spherical sub-micrometer particles with clean, smooth surfaces are key materials used as composite reinforcements, abrasives, and tribological additives, but remain synthetically challenging to produce. Pulsed laser melting in liquids (LML) is an environmentally friendly, emerging route for producing such particles. However, demonstrations have so far been limited to batch reactors, which are difficult to scale up to industrial production. Here, we extend laser melting in liquids to a continuous flat jet flow-through reactor in which boron carbide composite nanoparticles (B 4 CC) dispersed in ethanol are fed perpendicular to a nanosecond pulsed high-power ultraviolet laser beam; this is complemented by additional experiments employing pristine boron carbide. We elucidate how flow conditions and the application of modern high-repetition-rate lasers alter particle formation pathways. Characterization of B 4 CC, irradiated at fluences of 45–135 mJ·cm −2 , by transmission electron microscopy and dynamic light scattering, evidences the formation of a bimodal size distribution of spherical particles with mean diameters of ≈50 and ≈100 nm, verifying the parallel occurrence of isochoric reshaping and an aggregation–melting–fusion mechanism. While the smaller particle size fraction formed in accordance with thermal equilibrium calculations, the second size mode, derived from a multistep aggregation–melt–fusion pathway, was significantly smaller than predicted. Systematic variation of the number of laser pulses per unit volume (PPV) from 1 to 16 by tuning the interpulse delay (τ IP ) from 1.4 to 0.1 ms revealed an initial increase of the mean diameter of the second mode with PPV, reaching maximum size at 4 PPV. Interestingly, at higher PPV, further particle growth is arrested, probably due to an interplay between low particle mass concentration and shorter τ IP limiting the number of aggregation–melt–fusion steps, indicating kinetically controlled particle formation pathways. If the laser fluence is increased to 180 mJ·cm −2 , laser fragmentation in liquid prevails, and small mass fractions of ultrasmall nanoparticles (approx. 2 nm) are formed, which constitutes the upper limit of the LML process window. Overall, at the example of the ultrahard material boron carbide, difficult to process by other methods into perfect spheres, kinetically controlled LML in a flat jet flow-through reactor gives access to nanostructures in a size range previously unattainable by laser processing, establishing the basis for upscaling production in liquid flow with matched laser pulse numbers.

Direct answer

What can I do from this paper page?

Use this page to scan "Kinetically controlled boron carbide composite sub-micrometer particle formation pathways during continuous-flow laser melting in liquids with high-power lasers" quickly: start with the summary and abstract, then check the authors, source, topics, and related papers. From here, open Scollr to follow Laser-Ablation Synthesis of Nanoparticles research, save the paper, or map adjacent work.

Authors

Researchers on this paper

Nico Koch

first | University of Duisburg-Essen | ORCID 0009-0002-7247-8321

Christoph Rehbock

middle | University of Duisburg-Essen | ORCID 0000-0002-4708-5246

Naoto Koshizaki

middle | Hokkaido University | ORCID 0000-0003-4491-7200

Stephan Barcikowski

last | University of Duisburg-Essen | ORCID 0000-0002-9739-7272

Research areas

Follow related topics

Citation

BibTeX

@article{Koch2026Kinetically,
  title = {Kinetically controlled boron carbide composite sub-micrometer particle formation pathways during continuous-flow laser melting in liquids with high-power lasers},
  author = {Nico Koch and Christoph Rehbock and Naoto Koshizaki and Stephan Barcikowski},
  journal = {Beilstein Journal of Nanotechnology},
  year = {2026},
  doi = {10.3762/bjnano.17.108},
  url = {https://doi.org/10.3762/bjnano.17.108}
}

FAQ

Using this paper in a discovery workflow

How do I find related work for this paper?

Use the related papers and topic links on this page as starting points. In Scollr, you can also open the paper and build a literature map around its references, citing papers, and related work.

How can I keep up with new Laser-Ablation Synthesis of Nanoparticles research papers?

Follow Laser-Ablation Synthesis of Nanoparticles research in Scollr. New papers from the topic flow into a personalized feed, and you can save useful studies to revisit later.

Can I cite this paper from this page?

This page includes a static BibTeX block for Kinetically controlled boron carbide composite sub-micrometer particle formation pathways during continuous-flow laser melting in liquids with high-power lasers. Always verify the DOI, source, and publication details against the publisher record before submitting a manuscript.

Follow this research in Scollr

Follow the topics and authors behind this paper, save useful studies, and build a literature map when you are ready to go deeper.

Get the app